Page 3 of 3 FirstFirst 123
Results 21 to 26 of 26

Thread: Impact snaps

  1. #21
    Challenge Tour Pro
    Join Date
    May 2017
    Location
    Yeovil
    Posts
    694

    Re: Impact snaps

    It depends on who put the club together in the first place. When I am putting a shaft I leave the ferrule proud of the hosel by a few mm and wait for the glue to set before pushing the ferrule in to place. I have taken apart many a club where the same system has been employed.

    One of the differences is whether or not the hosel / ferrule is shouldered if yes I push it in to place before the glue sets otherwise the ferrule will not go in to place.


    I have never been able to move a ferrule if it has been glued in to place simply by hot water/steam.

  2. #22
    Tour Rookie londonlewis's Avatar
    Join Date
    Apr 2013
    Location
    Surrey
    Posts
    1,361

    Re: Impact snaps

    Quote Originally Posted by jim8flog View Post
    Nothing if all that is wrong is the hosel is loose. They only stay in pace by shrinkage and if you wash your clubs you should only do so in warm water. The way to move them is to pour hot water over them so they expand and move them in to the right position. Some builders will glue them in to place.


    To check if it is the shaft coming out of the hosel just grip the head and the shaft an try twisting it. If it does move then it will probably come out without applying heat. Clean the shaft and inside the hosel and refix using a two part epoxy resin. (plenty of 'how tos' on You Tube).
    Will let you know how I get on. Am playing golf on Saturday so keen to see if I can sort it before then.
    thanks for the advice.
    I discuss forum threads, therefore I am

  3. #23
    Global Moderator Twire's Avatar
    Join Date
    Nov 2008
    Location
    Exeter..ish - Devon
    Posts
    3,249

    Re: Impact snaps

    Quote Originally Posted by jim8flog View Post
    It could possibly be that too much of the chrome was taken off.

    These days when I fit a shaft I try to ensure that some of the chromed area is inside the hosel. I also try to take off only as much chrome as is needed for the shaft to fit in the hosel and get a good 'key' for the epoxy.

    However I would have though that with a company like Titleist that they have some sort of jig to ensure that the amount of the shaft that is de-chromed is fixed.
    Can I ask why you take the chrome off?
    We don't stop playing because we grow old.....We grow old because we stop playing.

  4. #24
    Challenge Tour Pro
    Join Date
    May 2017
    Location
    Yeovil
    Posts
    694

    Re: Impact snaps

    Quote Originally Posted by Twire View Post
    Can I ask why you take the chrome off?
    1. The chrome adds extra thickness and the shafts may not fit the hosel properly as a raw shaft, most notable on taper shafts which may appear to fit but are not properly bottoming out.

    2. It creates a rougher surface to which the epoxy will bond better.

  5. #25
    Global Moderator Twire's Avatar
    Join Date
    Nov 2008
    Location
    Exeter..ish - Devon
    Posts
    3,249

    Re: Impact snaps

    Quote Originally Posted by jim8flog View Post
    1. The chrome adds extra thickness and the shafts may not fit the hosel properly as a raw shaft, most notable on taper shafts which may appear to fit but are not properly bottoming out.

    2. It creates a rougher surface to which the epoxy will bond better.
    The shafts will be measured with chrome on so if they don't fit it's the wrong size tip.

    Yes it will create a rougher surface but if you have the correct epoxy it's not needed.
    We don't stop playing because we grow old.....We grow old because we stop playing.

  6. #26
    Challenge Tour Pro
    Join Date
    May 2017
    Location
    Yeovil
    Posts
    694

    Re: Impact snaps

    Quote Originally Posted by Twire View Post
    The shafts will be measured with chrome on so if they don't fit it's the wrong size tip.

    Yes it will create a rougher surface but if you have the correct epoxy it's not needed.
    I have got shafts here that have come from virtually everyone of the major manufacturers , clubs that is, and all of them rough up the tip.

    I have only got unprepped TTDG R300 and TT TX90 shafts at the moment and both measure 0.374 at the tip and not .370

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Latest Golf News

11 Of The Best Golf Shoes 2017

Best Golf Shoes 2017 - New technology and styling mean there has never been as much choice in the golf shoe market. Here are 11 of the best golf shoes 2017

October 18, 2017

The CJ Cup Golf Betting Tips

The PGA Tour are holding their first event in South Korea, check out who we think will do well with our The CJ Cup Golf Betting Tips

October 18, 2017

Andalucia Valderrama Masters Golf Betting Tips

Andalucia Valderrama Masters Golf Betting Tips - Can anyone beat Sergio Garcia and Jon Rahm to the title over the incredible Valderrama test

October 17, 2017

South Korea welcomes PGA Tour for CJ Cup

The PGA Tour heads to South Korea this week for the inaugural CJ Cup @ Nine Bridges. An elite, restricted field including Justin Thomas, Jason Day and Adam Scott will tee it up.

October 17, 2017

Sergio Garcia defends and hosts Valderrama Masters

The Andalucia Valderrama Masters returns to the European Tour schedule for the first time since 2011. Sergio Garcia defends and acts as tournament host.

October 17, 2017